This is a working overview of Primary drying, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2026-02-22 and is reviewed periodically as new material appears.
Lyophilization, or freeze-drying, removes water from a material by freezing it and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intervening liquid state. It is used for heat-sensitive materials that would degrade in conventional drying. The three stages are freezing, primary drying, and secondary drying, each with distinct temperature and pressure requirements. In practice, cycle design balances these variables.
Freezing determines ice crystal structure and pore size, which affect drying speed and product uniformity. Rapid freezing creates small crystals, while slow freezing creates larger crystals and often faster sublimation. During primary drying, chamber pressure is held below the vapor pressure of ice, and shelf temperature supplies heat for sublimation. The ice front recedes, leaving a porous matrix. Thermal limits such as collapse and eutectic temperatures set safe boundaries for formulation. These limits vary with solute composition and concentration.
Secondary drying removes bound water that remains after ice sublimation. Shelf temperature is raised gradually while pressure remains low, reducing water content to a target range. Over-drying can cause brittleness or electrostatic issues, while under-drying affects stability. The endpoint is often judged by pressure rise tests, temperature measurements, or water content analysis. Scale-up depends on matching heat and mass transfer across equipment sizes. Small changes in shelf temperature or pressure can alter cycle length substantially.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
| Property | Value | Notes |
|---|---|---|
| Process name | Lyophilization or freeze-drying | Both terms appear in technical standards and literature. |
| Phase transition | Sublimation | Solid ice becomes vapor without a liquid step. |
| Typical chamber pressure | 0.05-0.5 mbar | Range depends on product temperature and equipment. |
| Typical product temperature | -40 °C to -10 °C | Measured during primary drying; formulation sets limits. |
| Water content after drying | 0.5-3% w/w | Target varies by material and stability needs. |
The physical chemistry of freezing influences whether a formulation forms an amorphous glass or a crystalline solid. Amorphous systems can collapse if product temperature rises above the glass transition temperature of the freeze concentrate. Crystalline systems may show eutectic melting, where ice and solute melt together at a fixed temperature. Formulators add bulking agents, lyoprotectants, and buffers to preserve structure and biological activity. The optimum cycle keeps product temperature below critical thresholds during primary drying while allowing efficient sublimation.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
A formulation often contains excipients that protect the active ingredient during freezing and drying. Bulking agents provide structure, while lyoprotectants stabilize sensitive molecules. The freezing step can produce ice crystals whose size and distribution affect the drying rate, and cycle design includes freezing, annealing, and drying phases. If the product temperature rises above a critical value, the cake may collapse or lose its porous structure. Successful lyophilization therefore depends on the interaction between formulation, equipment, and cycle design.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
Auditory evoked potentials (AEP) can be used to trace the signal generated by a sound through the ascending auditory pathway. The evoked potential is generated in the cochlea, goes through the cochlear nerve, through the cochlear nucleus, superior olivary complex, lateral lemniscus, to the inferior colliculus in the midbrain, on to the medial geniculate body, and finally to the cortex. Auditory evoked potentials (AEPs) are a subclass of event-related potentials (ERPs). ERPs are brain responses that are time-locked to some "event", such as a sensory stimulus, a mental event (such as recognition of a target stimulus), or the omission of a stimulus. For AEPs, the "event" is a sound. AEPs (and ERPs) are very small electrical voltage potentials originating from the brain recorded from the scalp in response to an auditory stimulus, such as different tones, speech sounds, etc. Brainstem auditory evoked potentials are small AEPs that are recorded in response to an auditory stimulus from electrodes placed on the scalp. AEPs serve for assessment of the functioning of the auditory system and neuroplasticity. They can be used to diagnose learning disabilities in children, aiding in the development of tailored educational programs for those with hearing and or cognition problems.
ASBMB Award for Exemplary Contributions to Education ASBMB Leadership Awards ASBMB–Merck Award ASBMB Young Investigator Award Avanti Award in Lipids Bert and Natalie Vallee Award in Biomedical Science DeLano Award for Computational Biosciences Earl and Thressa Stadtman Distinguished Scientist Award Earl and Thressa Stadtman Young Scholar Award Herbert Tabor Research Award Mildred Cohn Award in Biological Chemistry - The Mildred Cohn Award in Biological Chemistry was established in 2013 to honor the scientific achievements of Mildred Cohn. Cohn was the first female president of the society, in 1978. The award of $5,000 is presented annually to a scientist who has made substantial advances in understanding biological chemistry using innovative physical approaches. The recipient is expected to deliver the Mildred Cohn Award lecture at the annual meeting. Ruth Kirschstein Diversity in Science Award The Alice and C. C. Wang Award in Molecular Parasitology Walter A. Shaw Young Investigator Award in Lipid Research William C. Rose Award
Binding curves describe the binding behavior of ligand to a protein. Curves can be characterized by their shape, sigmoidal or hyperbolic, which reflect whether or not the protein exhibits cooperative or noncooperative binding behavior respectively. Typically, the x-axis describes the concentration of ligand and the y-axis describes the fractional saturation of ligands bound to all available binding sites. The Michaelis Menten equation is usually used when determining the shape of the curve. The Michaelis Menten equation is derived based on steady-state conditions and accounts for the enzyme reactions taking place in a solution. However, when the reaction takes place while the enzyme is bound to a substrate, the kinetics play out differently. Modeling with binding curves are useful when evaluating the binding affinities of oxygen to hemoglobin and myoglobin in the blood. Hemoglobin, which has four heme groups, exhibits cooperative binding. This means that the binding of oxygen to a heme group on hemoglobin induces a favorable conformation change that allows for increased binding favorability of oxygen for the next heme groups. In these circumstances, the binding curve of hemoglobin will be sigmoidal due to its increased binding favorability for oxygen. Since myoglobin has only one heme group, it exhibits noncooperative binding which is hyperbolic on a binding curve.
The Bergmann degradation makes use of the azide degradation described by the Curtius rearrangement. Curtius also attempted to degrade benzoylated amino acids; however, his method involved splitting the carbamate with strongly energetic treatment with acids, which lead to decomposition of the resultant aldehyde and acid amides. This convinced Bergmann that Curtius' azide degradation could be followed by treatment with benzyl alcohol (his carbobenzoxy method) to isolate the resultant amino acid aldehyde and residual peptide amide for sequencing purposes.
Sources: en.wikipedia.org
Treatments for ATTR-related neuropathy include TTR-specific oligonucleotides in the form of small interfering RNA (patisiran) or antisense inotersen, the former having recently received FDA approval. Research into treatments for ATTR amyloidosis have compared liver transplantation, oral drugs that stabilize the misfolding protein (including tafamidis and diflunisal), and newer therapeutic agents still being investigated (including patisiran). Based on available research, liver transplant remains the most effective treatment option for advanced ATTR amyloidosis, protein stabilizing drugs may slow disease progression but were insufficient to justify delay of liver transplant, and newer agents such as patisiran require additional studies. Peptide synthesis Proteinopathy
Smith was hired to become the defensive quality control coach for the Tennessee Titans in 2011 under new head coach Mike Munchak. Smith then became the offensive quality coach the following season. In 2013, Smith was promoted to the assistant offensive line and assistant tight ends coach. Munchak was fired after the 2013 season and new head coach Ken Whisenhunt retained Smith as the assistant tight ends coach. Midway through the 2015 season, Whisenhunt was fired and replaced by tight ends coach Mike Mularkey. Mularkey was kept as head coach for the 2016 season and Smith was promoted to the new tight ends coach. When Mularkey was fired after the 2017 season, new head coach Mike Vrabel kept Smith as the tight ends coach for 2018. On January 21, 2019, Smith was promoted to offensive coordinator, replacing Matt LaFleur, who departed to become head coach of the Green Bay Packers two weeks prior. In his first year as offensive coordinator, Smith oversaw the highest-scoring Titans team in 16 years, with Derrick Henry, Ryan Tannehill, and Jonnu Smith having career years. Smith was praised for his play-calling in the Titans' 28–12 road victory over the top-seeded Baltimore Ravens in the AFC Divisional Round. In 2020, the Titans ranked fourth in scoring and second in total yards.
In addition to cell signaling, the mTOR pathway also plays a role in beta cell growth leading to insulin secretion. High glucose in the blood begins the process of the mTOR signaling pathway, in which leucine plays an indirect role. The combination of glucose, leucine, and other activators cause mTOR to start signaling for the proliferation of beta cells and the secretion of insulin. Higher concentrations of leucine cause hyperactivity in the mTOR pathway, and S6 kinase is activated leading to inhibition of insulin receptor substrate through serine phosphorylation. In the cell the increased activity of mTOR complex causes eventual inability of beta cells to release insulin and the inhibitory effect of S6 kinase leads to insulin resistance in the cells, contributing to development of type 2 diabetes. Metformin is able to activate AMP kinase which phosphorylates proteins involved in the mTOR pathway, as well as leads to the progression of mTOR complex from its inactive state to its active state. It is suggested that metformin acts as a competitive inhibitor to the amino acid leucine in the mTOR pathway.
The G protein-coupled receptor kinases (GRKs) are protein kinases that phosphorylate only active GPCRs. G-protein-coupled receptor kinases (GRKs) are key modulators of G-protein-coupled receptor (GPCR) signaling. They constitute a family of seven mammalian serine-threonine protein kinases that phosphorylate agonist-bound receptor. GRKs-mediated receptor phosphorylation rapidly initiates profound impairment of receptor signaling and desensitization. Activity of GRKs and subcellular targeting is tightly regulated by interaction with receptor domains, G protein subunits, lipids, anchoring proteins and calcium-sensitive proteins. Phosphorylation of the receptor can have two consequences:
RGD-based peptides have found many applications in biological research and medical devices. Culture plates coated with peptides mimicking ECM proteins' adhesion motifs, which promote prolonged culture of human embryonic stem cells, are on the market. RGD is also a universally used tool in the construction of multifunctional "smart" materials, such as tumor-targeted nanoparticles. Further, RGD is widely used in tissue engineering to promote tissue regeneration.
Sources: en.wikipedia.org
CPC Scientific’s manufacturing processes primarily use solid-phase peptide synthesis (SPPS), first described by Robert Bruce Merrifield in 1963. SPPS allows peptides to be assembled stepwise on a solid support, enabling the preparation of long and complex sequences for use as active pharmaceutical ingredients (APIs), investigational drugs, and research materials. Researchers associated with the company have published studies involving peptide synthesis methodologies, including work related to hydrocarbon stapling. Products manufactured by the company have been used and cited in various scientific studies. Official website
Human chorionic gonadotropin is a glycoprotein composed of 237 amino acids with a molecular mass of 36.7 kDa, approximately 14.5kDa αhCG and 22.2kDa βhCG. It is heterodimeric, with an α (alpha) subunit identical to that of luteinizing hormone (LH), follicle-stimulating hormone (FSH), thyroid-stimulating hormone (TSH), and a β (beta) subunit that is unique to hCG. The α (alpha) subunit is 92 amino acids long. The β-subunit of hCG gonadotropin (beta-hCG) contains 145 amino acids, encoded by six highly homologous genes that are arranged in tandem and inverted pairs on chromosome 19q13.3 - CGB (1, 2, 3, 5, 7, 8). It is known that CGB7 has a sequence slightly different from that of the others. The two subunits create a small hydrophobic core surrounded by a high surface area-to-volume ratio: 2.8 times that of a sphere. The vast majority of the outer amino acids are hydrophilic. beta-hCG is mostly similar to beta-LH, with the exception of a Carboxy Terminus Peptide (beta-CTP) containing four glycosylated serine residues that is responsible for hCG's longer half-life.
Encapsulin shells compromise icosahedral complexes (12 vertices, 20 faces, 30 edges) formed as a result of self-assembly of protomers. These encapsulin shells have diameters between 24 and 42 nm and are defined by the HK97-fold of their shell protein. The HK97-fold protomer has a roughly triangular shape and consists of three conserved domains: the axial domain, the peripheral domain, and the extended loop. The size and symmetry of the capsid are defined by a triangulation number (T), which determines the number of subunits in the assembly. For example: T = 1 encapsulins (Thermotoga martima) consist of 60 protomers. T = 3 encapsulins (Pyrococcus furiosus) consist of 180 protomers. T = 4 encapsulins (Quasibacillus thermotolerans) consist of 240 protomers.
CCL7 is a multipotent chemokine involved in anti-bacterial, anti-viral and anti-fungal immune responses. For example, CCL7-mediated stimulation of CCR2 chemokine receptors on monocytes is participating in the elimination of Listeria monocytogenes infections by the recruitment of monocytes and TNF/iNOS-producing dendritic cells (TipDCs). Next, the role of the CCL7 was also observed in the mouse infected by West Nile Virus. The genetically deficient mice in CCL7 have increased mortality because of decrease in monocytes and neutrophils. Early induction of CCL7 downstream of TLR9 signaling also promotes the development of robust immunity to cryptococcal infections. Diseases associated with CCL7 dysregulation are observed. For example, an abnormal increase of CCL7 worsens many disorders, like HIV or lesional psoriasis. Furthermore, CCL7 is implicated in various immunological diseases, as ulcerative colitis, multiple sclerosis or nonatopic and atopic asthma. It seems, that the expression of CCL7 can activate an antitumor immune response.
Developing standards-based messaging, to allow for automated data exchange Creating an exchange network, to ensure specific laboratories receive the information most pertinent to their work Improving reporting capabilities Selection and implementation of the best information management system for the laboratory's needs Strengthening the information network by sharing technical resources across public health laboratories One effort by the Informatics program is PHLIP, the Public Health Laboratory Interoperability Project. PHLIP aims to establish reliable laboratory data exchange between state public health laboratories and the CDC by fostering collaboration in IT and laboratory science.
Sources: en.wikipedia.org
Conventional drying uses heat to evaporate liquid water, often at temperatures that can degrade sensitive materials. Lyophilization freezes the material first and then removes water by sublimation under vacuum. This avoids prolonged exposure to liquid water and high heat.
Lowering pressure reduces the boiling point of water and allows ice to sublimate at temperatures below freezing. Vacuum also limits convective heat transfer, so heat is usually supplied by shelves or radiation. The pressure must stay below the vapor pressure of ice at the product temperature.
The cycle typically includes freezing, primary drying, and secondary drying. Freezing solidifies water and sets the pore structure; primary drying removes bulk ice; secondary drying removes bound water. Some cycles add annealing or pre-freezing steps.
Primary drying removes ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, often under the same vacuum. The two stages differ in the water state being removed.